Arizona Fly Fishing Forums  

Go Back   Arizona Fly Fishing Forums > Arizona Fly Fishing > General Discussion

Thread Tools Display Modes
Old 11-28-2018, 09:50 PM
AJacks's Avatar
AJacks AJacks is offline
Senior Member
Join Date: May 2010
Location: Miami, AZ
Posts: 280
U-40 cork sealer

Does anyone seal their cork with this stuff? How has it worked for you?

Also I have a small chunk missing in the cork on one of my rods... about as big around as a pencil eraser but not as deep... what can be done to fix it? Or should I just get some fine sandpaper and smooth it out some?
Reply With Quote
Old 11-28-2018, 10:02 PM
AJacks's Avatar
AJacks AJacks is offline
Senior Member
Join Date: May 2010
Location: Miami, AZ
Posts: 280
I found most of the little chunk that was missing... I was think I could use a little wood glue or epoxy and glue it back in... then when it dries smooth out any remaining areas with fine grain sandpaper?
Reply With Quote
Old 11-29-2018, 07:52 AM
SAT's Avatar
SAT SAT is offline
Senior Member
Join Date: Oct 2011
Posts: 2,586
I would glue the missing piece back in. Then for smaller holes if you have any cork dust you can mix that with some wood glue and use it to fill in the smaller cracks and pits. Then smooth it with fine sandpaper as needed.
Reply With Quote
Old 12-03-2018, 06:57 PM
DrLogik's Avatar
DrLogik DrLogik is offline
Senior Member
Join Date: Sep 2012
Location: Charlotte, North Carolina
Posts: 241
I've built a fair number of rods but I don't consider myself a "builder" but here's my take based on my experience. U-40 or any cork sealer is a double-edged sword. I don't use any sealer.

Here's why...

Depending on which sealer you use the cork can take on what I feel is a fake, plastic gummy kind of feel. I don't like it. To me it negates the whole concept of the tactile grippy feel of cork.

Once the rod gets a few years on the handle the handle will get dirty and it is much harder to clean.

As far as the hole, I'd try to re-use the broken piece if you still have it and epoxy it back in the hole and sand it smooth. If you have any cork dust you can mix some into the epoxy and the repair will be less noticeable.
´¯`·.¸¸.·´¯`·.¸ ><(((((º>
`·.¸¸.·´¯`·.¸.·´¯`·.¸¸.·´¯`·.¸.·´¯`·.¸¸.·´¯`·.¸ ><(((((º>
¸¸.·´¯`·.¸ ><(((((º>
Reply With Quote
Old 12-04-2018, 12:16 PM
Sasquatch's Avatar
Sasquatch Sasquatch is offline
Join Date: Nov 2016
Location: Silver city nm
Posts: 66
I left the plastic heat shrink on my last couple rods. My buddy make fun of it but I like it. No more dried out cracked skin. Tempted to try the sealer on my other rods.
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -7. The time now is 04:18 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
Logos, Trademarks are property of their owners. Other content Copyright 2006-2015 . All Rights Reserved.